Ifm-electronic JN2300 Manuale Utente

Device manualInclination sensor 2 axesJN2300 80228165/00 04/2015UK

Inclination sensor JN10TxPGN2 4-byte V_effective , 4-byte aPeakTxPGN3 2-byte acceleration X, 2-byte acceleration Y, 2-byte acceleration Z7.5 Configur

UKInclination sensor JN118 Parameter mapping8.1 Communication profile proprietary (0x500 – 0x1303)Index Type Value Unit R/W Reset0x500 ASCII Device

Inclination sensor JN12Index Type Value Unit R/W Reset0x1200 UNSIGNED8 Transmit parameter groups number 2 activeTxPGN24 bytes v eff4 bytes a peak 0: i

UKInclination sensor JN138.2 System settings 0x2000 - 0x207F)Index Type Value Unit R/W Reset0x2000 UNSIGNED8 Device address defaul

Inclination sensor JN14Index Type Value Unit R/W Reset0x2046 UNSIGNED8 Set index for zero of the X / Y / Z axes0: no change 1: activate set zero; rela

UKInclination sensor JN15Index Type Value Unit R/W Reset0x207F UNSIGNED8 Factory reset1: make factory resetR/W8.2.1 Informative (0x2080 – 0x2082)Inde

Inclination sensor JN169 Angle definition (0x2044)To be able to adapt the inclination sensor to the different applications as easily as possible, the

UKInclination sensor JN17Value range for this option – Inclination value longitudinal (gradient angle): -90°…+90° – Inclination value lateral (angle o

Inclination sensor JN189.5 Explanatory exampleThe different angle definitions will be illustrated using a simple example� An excavator moves up and d

UKInclination sensor JN1910.3 Set zero point (0x2046)To set the zero point the sensor is rotated to the requested position and the current position i

Inclination sensor JN2Contents1 Preliminary note � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

Inclination sensor JN20Explanatory exampleInclination sensor installed at an angle in the coordinate system of the workpiece� The coordinate system of

UKInclination sensor JN2110.8 MEMS measuring cell temperature (0x2081)The temperature of the measuring cell is determined every 200 ms and updated in

Inclination sensor JN22The default setting of the programming key is:j4w+ZEgRKHAl5Y8=11 Status LEDThe integrated LED indicates the current device sta

UKInclination sensor JN23

UKInclination sensor JN310�5 Set teach (0x2042h) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 1910�6 Quadrant co

Inclination sensor JN41 Preliminary noteThis document applies to the device of type "inclination sensor" (art� no�: JN2300)� It is part of

UKInclination sensor JN5The connection terminals may only be supplied with the signals indicated in the technical data and/or on the device label and

Inclination sensor JN65 Scale drawing364,590752245605,36 Electrical connectionThe inclination sensors are fitted with two round 5-pole M12 connector

UKInclination sensor JN77 SAE J1939 interfaceThe inclination sensors have a standardised SAEJ1939 interface� All measured values and parameter groups

Inclination sensor JN87.2 Proprietary PDU format 1 protocolThe parameters of the JN2300 sensors are listed in a table that is accessed per 16-bit ind

UKInclination sensor JN97.3 Configuration examplesAddress target unit (ECU): 0x19Address control unit / master: 0x14Priority of the message: 3Example